【主营产品】prefix = "o" ns = "urn:schemas-microsoft-com:office:office"
主营：世界知名品牌的PLC、DCS系统备件 模块
①Allen-Bradley(美国AB)系列产品》
②Schneider(施耐德电气)系列产品》
③General electric(通用电气)系列产品》
④Westinghouse（美国西屋）系列产品》
⑤SIEMENS(西门子系列产品)》
⑥销售ABB Robots. FANUC Robots、YASKAWA Robots、KUKA Robots、
Mitsubishi Robots、OTC Robots、Panasonic Robots、MOTOMAN
Robots。
⑦estinghouse（西屋）： OVATION系统、WDPF系统、MAX1000系统备件
。
⑧Invensys Foxboro（福克斯波罗）：I/A Series系统，FBM（现场输入
/输出模块）顺序控制、梯形 逻辑控制、事故追忆处理、数模转换、输入/
输出信号处理、数据通信及处理等。Invensys Triconex: 冗余容错控制
系统、基于三重模件冗余（TMR）结构的zui现代化的容错控制器。
⑨Siemens(西门子)：Siemens MOORE， Siemens Simatic C1，Siemens
数控系统等。
⑩Bosch Rexroth（博世力士乐）：Indramat，I/O模块,PLC控制器,驱动
模块等。
◆Motorola（摩托罗拉）：MVME 162、MVME 167、MVME1772、MVME177等系列。
尊敬的顾客您好，为了更好的保障您的合法权益，购买前请仔细阅读以下内容：
1.价格说明 并非原价，请以询价为准。
价格说明 并非原价，请以询价为准。
价格说明 并非原价，请以询价为准。
2.由于市场波动频繁，本店所标价格，并非实价，请买家提前咨询 后再拍，感谢支持。
3.所售商品报价均为不含税价 ，如须开票，请和店主联系。
4.本店所售商品均为正品现货，图片实物拍摄。如果您订购产品超过 多件，请与我们联系，我们可以为您尽量提供折扣。
5本店产品分为全新原装、全新无包装，工程余货和二手四种货品。购买前请联系客服仔细核对货品、型号、数量。
6.本店所售商品保证质量，全新无包装和二手商品签收十五日出现问题均包退换，请放心购买。所有配件质保一年。因买家自己弄错产品型号、参数或剪脚、上机、错误接入电源、错误安装、保管不当、人为损坏等除外。
7.本店所售商品国内顺丰包邮，国外运费自理。支持十五天内有任何产品质量问题退换货，过期一切损失请自行承担。请大家在货物签收时一定仔细检查物品外观是否完好无损，数量是否短缺，配件是否齐全如发现有任何问题请不要签收并立即致电我们，货物一旦签收完毕，就代表双方对货物外表、数量、配件一致认可无争议。
拍下商品后,视为认可以上各项条款，谢谢合作！
In the injection molding machine, the most widely used control law is proportional, integral, differential control, referred to as PID control. When the actual parameters of the pressure, speed and temperature of the injection molding machine can not be completely and reliably mastered, or the accurate mathematical model can not be obtained, and other technologies of the control theory are difficult to adopt, the parameters must be determined by experience and on-site debugging. At this time, the application of PID control technology is the most convenient. That is, when we do not fully understand the actual injection pressure, speed, temperature, or can not obtain the above parameters through effective measurement means, the most suitable PID control technology. PID control, there are also PI and PD control in practice. PID control is based on the error of the system, using proportional, integral and differential to calculate the control quantity.
Proportional control is the simplest control method. The output of the controller is proportional to the input error signal. When there is only proportional control, the system output has steady-state error.
In the integral control, the output of the control system is proportional to the integral of the input error signal. For a control system of injection molding machine, if there is steady-state error after entering steady state, it is said that the control system has steady-state error or system with steady-state error for short. In order to eliminate the steady-state error, "integral term" must be introduced into the pressure, speed and temperature control of injection molding machine. The error of the integral term depends on the integral of time. With the increase of time, the integral term will increase. In this way, even if the error is very small, the integral term will increase with the increase of time, which will promote the output of the injection molding machine computer to increase, and further reduce the steady-state error until it is equal to zero. Therefore, the proportional integral (PI) control can make the injection molding machine system into steady state without steady-state error.
