TELEMECANIQUE XML-F160D2039控制模块培训教程

类目：其他
型号：XML-F160D2039
全国服务热线：+86 15270269218
手机：+86 15270269218
微信：+86 15270269218
QQ：3136378118
Email：stodcdcs@gmail.com

在线咨询

产品详情

主营DCS控制系统备件，PLC系统备件及机器人系统备件，
优势品牌：Allen Bradley、BentlyNevada、ABB、Emerson Ovation、Honeywell DCS、Rockwell ICS Triplex、FOXBORO、Schneider PLC、GE Fanuc、Motorola、HIMA、TRICONEX、Prosoft等各种进口工业零部件
TELEMECANIQUE XML-F160D2039控制模块培训教程

当变频器所测转速不再小于汽轮机低转数设置值，则自动恢复至正常状态。其中还包括汽轮机停机转数，当汽轮机转数小于某一转数，则变频器立刻停机，当前设置为300rpm。
（4）通讯故障保护
闭环运行状态下，当检测到系统发生通讯断线(通过心跳位进行判断)，则变频器侧将自动由闭环运行状态切换至开环运行状态继续运行。
2.3系统限制功能
（1）转矩限制功能
转矩限制值包括用户在DCS直接设置的转矩限制值以及伺服电流限制逻辑计算得到的转矩限制值。对于用户在DCS直接设置的转矩限制值。当系统反馈值还未达到系统给定值时，如果转矩输出值达到限制值后，将以限制值作为输出。比如，开环运行状态下，当转矩限制为30%时，如果尚未达到给定量，则PI输出一直限制在30%，分别在积分值与PI输出处进行限制。但是有一点，假如运行情况下转矩限制值为30%，此时上位机修改转矩限制值为20%，需要斜坡下降到20%，不能直接到20%，防止汽轮机出现转速巨大波动。
汽轮机汽门开度(伺服电流反馈值)达到汽轮机汽门开度限制值(伺服电流设定值)后，计算得出的当前转矩输出值。转矩限制逻辑中，将以较小的数值为准。
（2）发电量限制功能
发电量限制值由用户直接在上位机上设定。开环状态时，发电量限制由变频器输入功率直接进行判断。当变频器输入功率达到发电量限制值时，则将给定信号进行限制。闭环状态时，给定值为进线功率目标值，反馈值为实际进线功率。此时的发电功率限制值，同样与变频器输入功率进行比较，变频器输入功率的达到发电功率限制值后，需要对进线功率目标值进行修正。controlled by internal program instructions. The contact of the output relay is connected with the output terminal of PLC to control the external output equipment, and its state is controlled by the internal program instruction. The auxiliary relay is equivalent to the intermediate relay in the relay control system, and its contact cannot directly control the external output equipment. The time relay is also called timer. After the timing value of 0 timer is determined, once the timer is started, it starts to decrease (or increase) in a certain unit (e.g. 10ms). When the time value set in the timer decreases to 0 (or increases to the set value), the contact of the timer will act. Counting relay is also called counter. After the count value of each counter is determined, once the counter is started, each pulse comes. The count value decreases (or increases) by 1 until the set count value decreases to 0 (or increases to the set value), and the output contact of the counter acts. It is worth noting that the above "soft relay" is only an equivalent relay. There is no such actual relay in PLC, and there is no corresponding