欢迎您访问:瑞昌明盛自动化设备有限公司,我司将竭诚为您服务!
170ENT11000库存可编程控制模块

主页 > 产品中心 > 140系列PLC

170ENT11000库存可编程控制模块

类目:140系列PLC
型号:170ENT11000
全国服务热线:+86 15270269218
手机:+86 15270269218
微信:+86 15270269218
QQ:3136378118
Email:stodcdcs@gmail.com

在线咨询
产品详情

170ENT11000库存可编程控制模块 170ENT11000库存可编程控制模块 170ENT11000库存可编程控制模块
瑞昌明盛进出口贸易有限公司
主营DCS控制系统备件,PLC系统备件及机器人系统备件,
优势品牌:Allen Bradley、BentlyNevada、ABB、Emerson Ovation、Honeywell DCS、Rockwell ICS Triplex、FOXBORO、Schneider PLC、GE Fanuc、Motorola、HIMA、TRICONEX、Prosoft等各种进口工业零部件
170ENT11000库存可编程控制模块 170ENT11000库存可编程控制模块 170ENT11000库存可编程控制模块
【利用当前显示单位发送稳定的重量值】
其中,“11”为事务号,“04”为要通过串口发送的数据长度。
PROFIBUS侧接收响应:
A1 53 20 53 20 20 20 20 20 20 20 33 39 2E 37 20 67 0D 0A 【HEX】
S S       39.7 g【ASCII】
其中,“A1”为事务号。
四、应用总结
该系统的应用,成功解决了远程监控现场原料投放量的问题。该系统已投入运行一年多时间,未发生任何硬件故障。其性能的稳定可靠,保证了现场生产工作的有序运行,取得了业主的一致好评。2010年5月,上海泗博自动化技术有限公司的Modbus转PROFIBUS-DP网关产品PM-160成功应用于上海世博园区世博中心的储能空调控制系统。
系统要求:通过西门子S7-300 PLC监控开利冷机30HXC螺杆机组运行情况及控制螺杆机组的开、关机以及出水温度等。系统使用的螺杆机组通讯接口为RS485,采用的是Modbus RTU通讯协议。
系统要求采集的部分数据如下:
Modbus PROFIBUS
Modbus PROFIBUS
系统实现:根据现场需要监控的螺杆机组的参数情况,每台Modbus转PROFIBUS-DP网关(PM-160)的Modbus RS485端口接两台螺杆机组,10台冷机螺杆机组共使用了5台Modbus转PROFIBUS-DP 网关(PM-160)。在网关PM-160的配置软件GT-123中配置相关的命令及串口通信参数,在PLC的组态页面进行相关组态(根据网关PM-160对应的GSD文件,在PROFIBUS-DP主站网络下组态5个PROFIBUS-DP从站)后即可实现数据传输。
配置方式:       GT-123是上海泗博自动化提供的免费配置软件,用户可在配置软件中配置Modbus转PROFIBUS-DP网关需要的参数及读写命令,建立Modbus寄存器起始地址和网关PM-160的内存地址的映射关系。配置界面如下所示:
Modbus PROFIBUS
Modbus PROFIBUS
GT-123配置界面The opening and closing of the glue spraying head is realized by the reversing of the solenoid valve. When the glue melting pressure reaches the set value, the solenoid valve is powered on and reversed, and the glue spraying head is opened to start glue spraying; When the set time is reached, the solenoid valve loses power and then reverses, and the glue spraying head is closed. 2.3 compensation algorithm of precision control solenoid valve is an actuator with large time delay. Its opening and closing need to go through a certain time, although this time is only milliseconds, and when the moving speed of glue spraying head is low, the error caused by the delayed opening or closing of solenoid valve is small. Considering the factors of production efficiency, it is inevitable to improve the moving speed of glue spraying head, but the resulting error also increases significantly. In order to reduce the influence caused by this error as much as possible, based on the analysis