欢迎您访问:瑞昌明盛自动化设备有限公司,我司将竭诚为您服务!
Ovation 405A675G21据高速通道模块现货

主页 > 产品中心 > EMERSON艾默生

Ovation 405A675G21据高速通道模块现货

类目:EMERSON艾默生
型号:405A675G21
全国服务热线:+86 15270269218
手机:+86 15270269218
微信:+86 15270269218
QQ:3136378118
Email:stodcdcs@gmail.com

在线咨询
产品详情

Ovation  405A675G21据高速通道模块现货 Ovation  405A675G21据高速通道模块现货 Ovation  405A675G21据高速通道模块现货
瑞昌明盛进出口贸易有限公司
主营DCS控制系统备件,PLC系统备件及机器人系统备件,
优势品牌:Allen Bradley、BentlyNevada、ABB、Emerson Ovation、Honeywell DCS、Rockwell ICS Triplex、FOXBORO、Schneider PLC、GE Fanuc、Motorola、HIMA、TRICONEX、Prosoft等各种进口工业零部件
Ovation  405A675G21据高速通道模块现货 Ovation  405A675G21据高速通道模块现货 Ovation  405A675G21据高速通道模块现货
监控主机与CJ1G通过RS232线缆连接。两级系统之间的通信采用的OMRON的现场总线协议CompoBus/S完成。
CompoBus/S通信模式可分为远距离通信和高速通信两种。当工作模式为远距离通信模式时,传输速率为83.75Kbps,传输距离可达500m; 当为高速通信模式时,传输速率为750Kbps,传输距离为100m。通信模式通过I/O连接单元的DIP开关设定。本系统选择远距离通信模式。
由于集中控制级的实现比较简单,这里只是介绍现场级控制柜PLC(一孔)的接线图与软件实现。现场级控制柜的接线原理图如图2。
PLC 由UPS电源提供220VC 电源。PLC的0CH和1CH为输入通道,100CH和101CH为输出通道。其0CH通道的低8位I:0.00~I:0.07接旋转编码器,进行闸门开度状态的采集。0CH通道高4位进行现场闸门控制操作以及系统其他一些状态的采集。在1CH(输入)通道中I:1.08进行现场/集中控制的选择。I:1.09是为了清除错误报警位设立,当错误排出后,对I:1.09的输入使得错误信息复位,系统可以运行。1CH后两位提供了闸门运行的一种保护。
输出通道100CH的输出为闸门的控制信号以及提示、报警信息。图中的IN1+、IN1一为模拟量输入通道。它与水位仪连接。由于CP1H系列PLC提供了一个24VDC的电源输出,所以可以直接作为水位仪的电源。
图片加载中…
图2     PLC现场接线原理图
4 软件设计
现场一号控制柜的软件编写如下:系统的自动控制功能可分为现场级控制、集中开/闭环控制。其控制的程序流程图如图3。现场控制级具有高的优先级,这是由于对闸门的控制要求有较高的安全性和可靠性。当选择现场级控制后,集中开/闭环控制都被屏蔽。PLC采集现场控制柜的升、降、停控制输入状态,对闸门进行升降停操作。此时闸门的开度信息、运行状态可以在现地控制柜上的文本显示屏进行显示输出,并同时上传到监控主机显示。如发生错误,则发出报警并停止闸门运行。(3) Keep the PLC operation switch off and set the program to the monitoring state. Press the button on the touch screen to observe the action of the program contact. If the action is incorrect, check whether the touch screen attribute setting corresponds to the program.

(4) The system time shall be displayed correctly.

(5) Change the value of the input register on the touch screen and observe the change of the value of the register corresponding to the program.

(6) Connect the I / O line of PLC and the control circuit and main circuit of frequency converter according to (Fig. 4-1).

(7) Keep the PLC operation switch on and set the water pressure to 3kg.

(8) Start manually, and the equipment shall start normally. Observe whether the operation of each equipment is normal, whether the output frequency of the frequency converter is relatively stable, and the deviation between the actual water pressure and the setting.

(9) If the water pressure fluctuates violently above and below the set value, the differential parameters of PID command should be adjusted to set the value smaller,