欢迎您访问:瑞昌明盛自动化设备有限公司,我司将竭诚为您服务!
REXRTOH R911318626 MKD115B-024-KG1-AA伺服控制器备件

主页 > 产品中心 > 力士乐

REXRTOH R911318626 MKD115B-024-KG1-AA伺服控制器备件

类目:力士乐
型号:R911318626 MKD115B-024-KG1-AA
全国服务热线:+86 15270269218
手机:+86 15270269218
微信:+86 15270269218
QQ:3136378118
Email:stodcdcs@gmail.com

在线咨询
产品详情

REXRTOH  R911318626 MKD115B-024-KG1-AA伺服控制器备件 REXRTOH  R911318626 MKD115B-024-KG1-AA伺服控制器备件
瑞昌明盛进出口贸易有限公司
主营DCS控制系统备件,PLC系统备件及机器人系统备件,
优势品牌:Allen Bradley、BentlyNevada、ABB、Emerson Ovation、Honeywell DCS、Rockwell ICS Triplex、FOXBORO、Schneider PLC、GE Fanuc、Motorola、HIMA、TRICONEX、Prosoft等各种进口工业零部件
REXRTOH  R911318626 MKD115B-024-KG1-AA伺服控制器备件 REXRTOH  R911318626 MKD115B-024-KG1-AA伺服控制器备件 REXRTOH  R911318626 MKD115B-024-KG1-AA伺服控制器备件

REXRTOH  R911318626 MKD115B-024-KG1-AA伺服控制器备件
其中溶解罐体积为0.5立方米,玻璃钢复合而成,储药箱体积为1.5立方米,玻璃钢复合而成。在加药装置使用前,应对相应系统管路进行清洗,防止异物堵塞管路,打开T型过滤器前及泵出口的球阀、压力表阀,检查所有阀门的启闭无误。工作流程图如下图:
   原药液是通过人工加入溶解罐中的,要按配置药液浓度打开水阀加水稀释,溶解罐内液位达到搅拌液位时自动开启搅拌机,使溶解罐中的药剂与水充分溶解混合后自动关闭搅拌机,搅拌机运行时间一般为15到20分钟比较适宜(时间要根据现场实际情况定), 药液配好后启动计量泵进行投药,每套加药装置设二台计量泵,工作方式为一用一备,正常工作时为一台计量泵运行,当有一台计量泵出现故障时,自动切换到另一台计量泵,以保障投加药的连续性;在计量泵工作时,要观察泵出口压力表压力是否正常;要调整计量泵流量至工艺设计要求流量,计量泵设计流量为0-500升/小时。 (3)系统硬件配置       系统硬件部分:根据本系统的实际情况,设计了以LOGO !为主控单元的控制回路。LOGO!是西门子公司生产的具有输入输出功能可编程的逻辑控制模块,集成了8种基本功能与26种特殊功能,可代替数以百计的开关设备,不仅节约了成本费用,且缩短了工程时间。根据加药系统输入输出点的要求,选用LOGO! RC230主模块,其共计8个输入点和4个输出点,220VAC电压作为输入信号,继电器输出可采用220VAC电压。硬件照片如下图2、3。
(4)软件开发      软件部分:使用新编程软件
Soft Comfort V6.0编制功能块程序,该软件可视化程度高,编程方便,既可用功能块编程,又可用梯形图编程;可仿真模拟运行调试,调试完成后通过编程
电缆
下载到LOGO !模块中即可。      下面从以下几个部分对控制程序进行说明。项目中的数字量模拟量I/O分配如下表所示。
 
图4为加药装置自动控制功能块示意图,先在加药控制柜中给LOGO!上电并正常时,选择自动(I1信号有效),这时系统进入自动程序。
   首先系统通过磁翻板液位计检测药液液位,因为在配药过程中,药液液位平面始终是波动的,为了消除液位抖动对控制的影响,设置了接通延时定时器B001、B002去除抖动信号影响cases of the circuit, the normally open type is used, which is used to manually control or automatically control the connection and disconnection of the current; Normally closed type is mainly used in protection circuit. Thus, we can know how the normal state of switching and protection devices is, and identify the quality of devices. 6. The detection of communication module is to use the simple replacement of new communication module to identify whether the module in use on the board is normal.Measurement method of Conductor: the conductor is also carried out by detecting the on-off method. The known conducting wire can be used to detect whether it is good or bad. The method is to connect the good conductor with the unknown conductor and then measure the on-off state. 8. Resistance detection: detect the voltage when it is charged and the corresponding resistance when it is not charged. 4、 It is concluded that most faults in the work can be eliminated through detection. In addition,