欢迎您访问:瑞昌明盛自动化设备有限公司,我司将竭诚为您服务!
HONEYWELL 51401166-100模块系统备件现货

主页 > 产品中心 > HONEYWELL霍尼韦尔

HONEYWELL 51401166-100模块系统备件现货

类目:HONEYWELL霍尼韦尔
型号:HONEYWELL 51401166-100
全国服务热线:+86 15270269218
手机:+86 15270269218
微信:+86 15270269218
QQ:3136378118
Email:stodcdcs@gmail.com

在线咨询
产品详情
瑞昌明盛进出口贸易有限公司
主营DCS控制系统备件,PLC系统备件及机器人系统备件,
优势品牌:Allen Bradley、BentlyNevada、ABB、Emerson Ovation、Honeywell DCS、Rockwell ICS Triplex、FOXBORO、Schneider PLC、GE Fanuc、Motorola、HIMA、TRICONEX、Prosoft等各种进口工业零部件
HONEYWELL 51401166-100模块系统备件现货 HONEYWELL 51401166-100模块系统备件现货 HONEYWELL 51401166-100模块系统备件现货

HONEYWELL 51401166-100模块系统备件现货
称重单元主要由计量托辊和两个应变式荷重传感器组成。称重传感器安装在高精度的平台上,其测量出输送带上物料的单位长度重量;皮带测速单元采用高精度脉冲编码器安装在从动滚筒的轴端,通过滚筒转动产生脉冲信号,以上重量信号(毫伏级)及脉冲信号分别传送至积算控制系统。
其积算称重原理如下所示:
Q:输送量 (重量范围 0~t1) (kg)q:瞬时输送量 (kg/min)W:物料的单位长度重量 (kg/m) (载荷密度)V:皮带速率 (m/min)设输送带的运行长度为[l],输送带的速度为[v],输送带运行时间为[t], 其关系为l=vt因此在输送带运行了t1时间后,输送带的运行长度为l1=vt1,那么,输送流量可用下列方程式表示:
给料机的输送量为A,B,C三点所包围的面积。
如下图所示。
W = f (l) : 在任选的单位运行长度 [l] 上的载荷密度Wdl  : 在微小运行距离(dl)上的输送量
上述表明:要计算获得输送量,需通过称量传感器检测到煤流的单位长度的瞬时重量信号,同时速度传感器检测到速度脉冲信号。通过控制仪表将重量信号与速信号进行乘积运算,从而求得输送量,并通过输送量积算求得累积量。
3.工艺设备主要参数物料粒度:         0~80mm物料散密度:       800kg/m3物料水分:         10~12%物料温度:         常温给料方式:         圆盘给料皮带驱动电机:     3.7KW 3φAC380V圆盘驱动电机:     15KW 3φAC380V 轴端编码器:        600P/R DC12V~24V      给料机输送带宽度:       800mm输送机能力范围:      10~100t/h输送机速度:         0.1m/s~1m/s输送机倾斜角度:        0℃输送机头、尾滚筒中心距:  3m~3.5m配料秤系统精度:         优于0.5%
2.系统配置  本系统24台配煤秤分为两个工艺段各为12台,每个工艺段控制单元由1个S7-315-2DP CPU主站(含1个本地扩展主站)及2个ET200M从站、12个CFC-200及6SE70变频器配带CBP2从站所组成,两个工艺段控制单元经光纤工业以太网进行互连,两台带有WinCC V6.0的工控机组成配煤系统操作员站,其中一台兼有工程师站功能。

HONEYWELL 51401166-100模块系统备件现货

HONEYWELL 51401166-100模块系统备件现货
brake pedal is pressed gently by the driver, the energy in the high-pressure brake pedal will be gradually recovered; When the pressure in the high-pressure accumulator reaches the maximum value, the recovery process ends. When the driver gently steps on the accelerator pedal (or presses the manual release button), the device starts to release energy. At this time, the high-pressure oil in the high-pressure accumulator drives the hydraulic pump / motor to rotate, and the pressure of the high-pressure accumulator gradually decreases; When the pressure of the high-pressure accumulator is low to the minimum value, the release process ends. The typical configuration selects the CPU module lm3106 to control the hydraulic energy regeneration device. The lm3106 body integrates 14 point di / 10do. Its output is transistor type and has 2-way dual-phase high-speed counter, which can collect the speed of the bus driving device. The pressure of the hydraulic system is collected by the analog quantity acquisition module lm3310,