KJ3221X1-BA1 VE4005S2B2工控备件PLC模块现货

类目：EMERSON艾默生
型号：KJ3221X1-BA1 VE4005S2B2
全国服务热线：+86 15270269218
手机：+86 15270269218
微信：+86 15270269218
QQ：3136378118
Email：stodcdcs@gmail.com

在线咨询

产品详情

瑞昌明盛进出口贸易有限公司
主营DCS控制系统备件，PLC系统备件及机器人系统备件，
优势品牌：Allen Bradley、BentlyNevada、ABB、Emerson Ovation、Honeywell DCS、Rockwell ICS Triplex、FOXBORO、Schneider PLC、GE Fanuc、Motorola、HIMA、TRICONEX、Prosoft等各种进口工业零部件
KJ3221X1-BA1 VE4005S2B2工控备件PLC模块现货

该调度绞车在未采用变频器前,用户首先采用工频45KW电机高速将铁牛从牛棚里拉出,经过40min拉到位,与列车车厢连接,然后装车。采用55KW电机低速拖动车厢,由于用户出料口出料时多时少,绞车为配合列车装煤,需要频繁起动、停止,启动电流比较大,接触器的触点及线圈经常损坏,影响了列车的正常装车。为了提高装车效率,大屯选煤厂决定选用我山东新风光电子科技发展有限公司生产的JD-BP32-90T变频器对其调度绞车进行变频调速改造。改造达到了预期目的 ,现对改造方案作一介绍。
3 调度绞车变频控制系统
调度绞车变频控制系统设备包括变频
控制柜
PLC
、主操作台。
供电电源为AC380V,50Hz,三相四线制,由外部用户开关引至变频控制柜,内设总开关,其额定容量根据装机总容量选配,具有短路、过载、失压等多种保护功能。
控制及信号电源为AC220V，由单相隔离变压器供电，变频控制柜设有风机进行通风散热。主电路主要有变频器电机回路，控制回路主要有西门子PLC、检测元件、电磁阀、中间继电器及指示灯等组成。
（1）变频控制柜
内设保护变频器的断路器、风光变频器、及三相双掷开关等。
系统采用我山东新风光电子科技发展有限公司生产的提升机专用变频器，该产品具有较大的启动力矩、加速力矩和制动力矩，电机可在四象限运行，并且具有能量回馈单元，将制动时产生的再生能量回馈给电网。本产品除一般变频器所具有的过压、欠压、过载、短路、温升等多种保护功能外，还具有开机连锁保护，自动限速保护，完全适用调度绞车要求的力矩大，频繁启停、频繁加减速及四象限运行等运行特点，是矿用调度绞车变频改造的理想选择。变频器上的数字输入、数字输出接口与PLC相连，交接信息，随时控制调度绞车的运行速度。在变频器中可设置加减速时间，S形速度曲线加速,可大限度地减小启动过程中的机械冲击，对调度绞车具有较高的安全性。
（2）PLC控制柜
PLC控制系统采用德国西门子PLC系列，模块化结构，配置包含有数字输入、输出模块、模拟量模块、电源模块、CPU模块等。在本系统中采用采用西门子CPU224和模拟量模块EM232。CPU224有14个（I/O）输入接口和10个输出接口。模块EM232 控制变频器的运行频率，进而控制电机的转速。
PLC输入数字信号有：控制调度绞车运行的正转指令信号，反转指令信号，停机指令信号，低速指令，中速指令，急停指令，变频器故障复位，控制调度绞车的东限位开关信号，西限位开关信号，断绳保护信号，变频器故障信号.。PLC输出信号有开停机信号，正反转信号，复位，急停及各种状态指示信号。PLC的模拟量输出信号用来控制变频器的运行频率。PLC通过程序对输入指令信号进行各种逻辑处理，转换成一套高效执行的控制指令，控制执行元件，完成自动化控制功能。simple. However, it is often difficult to achieve in practical application, because some equipment must be grounded to ensure measurement accuracy or personal safety, and some equipment may form new grounding points due to long-term corrosion and wear or climate impact.

2) The second method:

Make the potential of the two grounding points the same, but because the grounding resistance is affected by many factors such as geological conditions and climate change, this method can not be completely achieved in practice.

3) The third method:

The signal isolator is used in each process link to disconnect the process loop without affecting the normal transmission of process signals, so as to completely solve the problem of ground loop.

3: Why does the use of signal isolator have good advantages?

The signal isolation method can be used in each process loop

DCS

PLC

And other isolation cards or field isolated transmitters (which can be achieved by sub equipment) can also be realized by signal isolator. In comparison, using signal isolator has the following advantages:

? In most cases, using signal isolator + non isolation card is cheaper than using isolation card

? Compared with the isolation card, the signal isolator has better performance in isolation ability and anti electromagnetic interference

? The isolator is more flexible in signal conversion and signal distribution

? Signal isolators usually have single channel and double channel, which are completely independent of each other, making the configuration and daily maintenance of the system more convenient.

4: Now there are so many brands of isolators in the market, and the prices are uneven. How to choose?

The isolator is located between two system channels, so when selecting the isolator, first determine the input and output function, and make the input and output mode of the isolator (voltage type, current type, loop power supply type, etc.) adapt to the interface mode of front and rear channels. In addition, there are many important parameters related to product performance, such as accuracy, power consumption, noise, insulation strength and bus communication function. For example, noise is related to accuracy, power consumption and heat are related to reliability, which need to be caref