MVME162-003工控备品PLC卡件现货

类目：MOTOROLA
型号：MVME162-003
全国服务热线：+86 15270269218
手机：+86 15270269218
微信：+86 15270269218
QQ：3136378118
Email：stodcdcs@gmail.com

在线咨询

产品详情

瑞昌明盛进出口贸易有限公司
主营DCS控制系统备件，PLC系统备件及机器人系统备件，
优势品牌：Allen Bradley、BentlyNevada、ABB、Emerson Ovation、Honeywell DCS、Rockwell ICS Triplex、FOXBORO、Schneider PLC、GE Fanuc、Motorola、HIMA、TRICONEX、Prosoft等各种进口工业零部件 MVME162-003工控备品PLC卡件现货

电气系统配置设计
2．1人机选用台达的文本显示器台达TP04
·STN LCD 128*64
·256K内存
·2个通讯口COM1(RS232) COM2(RS485)
·薄膜式按键
·DC24V(-10%-20%)
·内建万年历功能
·三种语言切换
·多种图形,按钮,组件功能.
2．2控制器
PLC
DVP32EH00R2
该机种为台达高功能主机,16入/16出. 具有以下特点
·2个通讯口,可以扩充到3个
·内建高速输入/输出
·200KHz高速计数器、200KHz脉波输出
·丰富的指令，功能强大，超稳定的电气特性。
2．3变频器
VFD022M43A--前牵引控制.
VFD022M43A---后牵引控制.
·迷你型微型化结构设计、体积小，易操作
·高度运行稳定性，性能完善，功能齐全
·载波频率高达18KHz，实现静音运转; 0.1-400Hz
·7段速控制及简易PLC自动程序运转
·高速通讯接口，达率高达38400bps
·自动加减速佳化控制功能
·智能化风冷技术应用
2．4烘箱部分
VFD055M43A*4循环风机,VFD055M43A排气
电机
将浸涂后的纤维布进入4个烘烤箱中烘烤，4个烘箱的温度由温控器控制，温控器选用台达的DTA4896，总共4个单独控制温度；总共4台VDF055M43A变频器拖动循环风机，1台3.7KW排废风机,选用VFD037M43A.
2．5收卷控制
收卷伺服控制：伺服电机ASMT30M250AK
伺服驱动器ASDA-A3021MA.
·五机一体
·内涵
运动控制
·性能优异
·指令平滑功能
·软件功能
·通讯功能通讯接口 RS232/RS485
·3种工作模式
·10种控制模式自由切换
·自动增益调整
·高响应,高均一性适应应.
2．6纠偏控制器+.同步电机控制纠偏,跟随2个位移传感器做位置跟随,防治跑偏。
2．7编码器测定纤维长度，1PLUSE/1MM
2．8电气系统结构图（图2）

3 文本画面规划

after each stop. In this way, when calculating the head and tail shear, the corresponding shear advance a should be corrected in order to obtain the accurate shear length.

Due to the different inertia of the mechanical device at different rolling speeds, the braking distance required for the stopping process is different. The faster the speed, the greater the braking angle required. In order to make the cutting edge stop at the zero position accurately after cutting, the braking angle shall be measured during head and tail cutting, that is, according to the pulse count value of the encoder on the cutting edge shaft, the rotation angle of the cutting edge from the power failure of the clutch brake solenoid valve coil to the complete stop of the cutting edge shall be obtained, and the average value measured in the latest several head and tail cutting braking shall be taken as the next head cutting Braking angle during tailing.

4 control function description

Searching for zero position: when the initial program is started, searching for zero position is essential. Due to the uncertainty of zero position pulse when the encoder is installed, after the system is started, the relative deviation between the shear edge position at the counting zero point of the encoder and the mechanical zero point must be determined. Otherwise, the physical position of the shear edge cannot be obtained according to the count value of the encoder, and the flying shear cannot be controlled. The specific process is as follows: after the system is started, press the inching switch on the local operation box to make the flying shear rotate slowly for more than two turns at the inching speed, then press a button in the box for at least 5 seconds (to prevent accidental misoperation), and then release the button. Rotating for two turns is mainly to check whether the counter board and encoder work normally.

Because the rolling speed signal sent from the rolling line speed control system is only calculated by the system according to the motor speed feedback value of the previous stand of cv50, combined with the mechanical reduction ratio and the roll diameter of the roll, and with the progress of production, the roll

With the continuous wear, the size of work roll diameter is also changing, and there is inevitably a deviation between the calculated speed and the actual rolling speed. In order to improve the shearing accuracy, it is necessary to measure the actual speed of the rolled piece in order to correct the speed used for tracking.

RELIANCE

ABB

GE

FOXBORO

EMERSON艾默生

A-B

MOTOROLA

TRICONEX

HONEYWELL霍尼韦尔

HIMA

140系列PLC

BENTLY本特利

其他

SST

EPRO

YOKOGAWA

MOOG

NI

WOODWARD伍德沃德

METSO

KOLLMORGEN科尔摩根

力士乐

ALSTOM阿尔斯通

YASKAWA安川

AMAT

ICS TRIPLEX

新能源系列

EATON

MVME162-003工控备品PLC卡件现货

扫一扫关注微信