Radisys 6040-0167计数板

产品详细资料
重置继电器上的所有警报和指示。继电器显示应保持不变，无跳闸指示。 对函数生成器进行编程，以模拟频率变化率刚好高于速率1。启动频率应为继电器的标称频率；如果继电器要工作，则结束频率必须低于频率衰减阈值。注意，如果满足速率标准并且频率低于阈值，则会发生操作。 一旦频率降至阈值以下，启动斜坡动作并验证元件操作。 检查跳闸和拾取指示灯是否亮起，并显示以下跳闸信息之一：锁定：频率衰减率1或操作：频率衰减速率1如果目标选择为锁定，跳闸指示灯和信息保持亮起。 将电压降至S4元件以下 频率 频率衰减 低工作电压电压监督水平。 重复斜坡动作，并确认元件不工作。如果电压监控水平已设置为0.00，则元件将继续正常运行，直至约2%或标称值。 将电压恢复到标称值。 如果启用电流感应，则将电流电平设置为S4 ELEMENTS（S4元件）以下 频率 频率衰减 小工作电流值。 重复斜坡动作，并确认元件不工作。 对于定时测试，如果计时器在斜坡动作的同时触发，并且测量触发点和继电器操作之间的时间间隔，则可以获得近似的操作时间。从测量的时间中减去频率达到阈值所需的时间。
Reset all alarms and indications on the relay. The relay display should remain unchanged with no trip indications.  Program the function generator to simulate a frequency rate-of-change just above rate 1. The start frequency should be the nominal frequency of the relay; the end frequency must be below the frequency decay threshold if the relay is to operate. Note that operation occurs if the rate criterion is satisfied and the frequency is below the threshold.  Initiate ramping action and verify element operation once the frequency drops below the threshold.  Check that the Trip and Pickup LEDs are on and one of the following trip messages is displayed: LATCHED: Freq Decay Rate 1 or OPERATED: Freq Decay Rate 1 If the target was selected as Latched, the Trip LED and the message remain on.  Reduce the voltage to below the S4 ELEMENTS  FREQUENCY  FREQUENCY DECAY  MINIMUM OPERATING VOLTAGE voltage supervision level.  Repeat ramping action and verify that element does not operate. If the voltage supervision level has been set to 0.00, the element continues to operate correctly down to approximately 2% or nominal.  Return voltage to nominal value.  If current sensing is enabled, set the current level below the S4 ELEMENTS  FREQUENCY  FREQUENCY DECAY  MINIMUM OPERATING CURRENT value.  Repeat ramping action and verify that element does not operate.  For timing tests, an approximate operate time is obtained if a timer is triggered at the same time as the ramping action and the time interval between the trigger point and the relay operation measured. From that measured time, subtract the time required for the frequency to reach the threshold value.
主营产品简介
专注于DCS、PLC、机器人控制系统、大型伺服四大系统领域。

主营产品各种模块/卡件，控制器，触摸屏，伺服驱动器。

优势：供应进口原装正品，专业停产配件，

发货快，货期精准，

主营品牌包括 ABB贝利、GE/FUANC、FOXBORO、英维思TRICONEX 、本特利BENTLY、A-B罗克韦尔、艾默生EMERSON 、OVATION、MOTOROLA、XYVOM、霍尼韦尔HONEYWELL 、力士乐REXROTH、KUKA、NI、DEIF、横河、伍德沃德WOODWARD、瑞恩、施耐德SCHNEIDER 、安川、 穆格MOOG、PROSOFT等品牌。

只卖库存产品;出完需订货!价格以客服说明为准!!订货货期以客服说明为准，有任何疑问请联繁客服! Limited stock, Contact US!

●使用前:

在操作和维护，安装设备之前，请阅读并严格遵守安全相关的信息。

Read and strictly follow safety-related information before operatingmaintainingand installing equipment.

●使用者要求:

必须从事安装，组装或维护设备等相关工控电气机械以及其他相关技术的人员。

Must be engaged in the installation,assembly or maintenance of equipment and other related industriacontroeectrica machinery and other related technica personne.应用范围:

应用于品牌本系列工业以及生产生活自动化设备产品。

Used in the brand of this series of industriaand production automation eauipment products

适用于场景:系统集成，非标定制，产线升级改造，原设备电气替换等等。

Suitable for scenarios:system integration,non-standard customizationproduction line upgrading and transformation,electrical replacement of original equipment,etc.

●操作人员:

应该由本品牌专业培训操作员来安装、操作和维修设备。专业人员具有技术能力强，熟悉安全信息和安全实施:

熟悉设备的安装加工、操作和维护:熟悉处理所有的潜在危险情况。

Equipment should be installed,operated and maintained by trained operators from the brand

●危险情况

警告

.请注意使用人员的人身安全。

●除了产品特性以及功能，还需了解产品的使用寿命环境。

●充分学习产品使用手册，否则非专业人员可能会造成人身危险。

Study the product instruction manual thoroughlyotherwise it may cause personal danger to non-professionals.

●服务行业

适用水泥，木业，石业，橡胶，石油，化工，发电，环保，水处理，制冷，交通，钢铁，食品，饮料，船舶，制冷等行业

Applicable to cementwood,stone,rubber,petroleumchemical, power generation