RADISYS EPC-9 61-0651-40中文说明

产品详细资料
远程复位模式验证 将差速器元件设置为锁定目标。 施加足够的电流使继电器工作，然后消除电流。跳闸指示灯和相位指示灯应锁定。 设置S1 745设置 复位 远程复位信号至逻辑输入1（16）。 断言逻辑输入1。目标应该重置。7.5.2.5固态输出的验证如果固态输出用于驱动辅助继电器， 验证这些继电器在继电器处于跳闸状态时是否工作。 确保通过辅助线圈的电流在每次测试之间被外部接触器中断。当固态输出直接操作断路器时，为了避免在调试过程中操作断路器， 使用下面所示的电路来验证此输出。每当继电器处于跳闸状态时，电流就会流过负载电阻器。 在继电器方案中使用的正常直流电源电压下，选择约1×CT直流电流的电阻器。要测量谐波抑制差动元件的基本工作时间， 通过双极单掷开关将交流电流信号连接到端子H1和G1。开关的第二极启动计时器电路，计时器电路因继电器跳闸触点的操作而停止。有关详细信息，请参阅下图。 闭合开关，将电流水平设置为先前测量的小拾取值的三（3）倍。
Verification of Remote Reset Mode  Set the differential element with a latched target.  Apply enough current to cause the relay to operate, then remove the current. The Trip LED and the Phase LED should be latched on.  Set S1 745 SETUP  RESETTING  REMOTE RESET SIGNAL to Logic Input 1(16).  Assert logic input 1. The target should reset. 7.5.2.5 Verification of Solid-state Output If the solid-state Output Is Used To Drive Auxiliary Relays,  Verify that these relays operate whenever the relay is in a trip condition.  Ensure that the current though the auxiliary coils is interrupted by an external contactor between each test. To avoid operating the breaker during the commissioning process when the solid-state output operates the breaker directly,  Use the circuit shown below to verify this output. Whenever the relay is in a trip state, current flows through the load resistor.  Select the resistor for approximately 1 × CT of DC current with the normal DC supply voltage used in your relay scheme.To measure the basic operating time of the harmonic restrained differential elements,  Connect an AC current signal to terminals H1 and G1, through a double-pole single-throw switch. The second pole of the switch starts a timer circuit which is stopped by the operation of the relay trip contact. Refer to the figure below for details.  Close the switch and set the current level to three (3) times the minimum pickup value measured earlier.
主营产品简介
专注于DCS、PLC、机器人控制系统、大型伺服四大系统领域。

主营产品各种模块/卡件，控制器，触摸屏，伺服驱动器。

优势：供应进口原装正品，专业停产配件，

发货快，货期精准，

主营品牌包括 ABB贝利、GE/FUANC、FOXBORO、英维思TRICONEX 、本特利BENTLY、A-B罗克韦尔、艾默生EMERSON 、OVATION、MOTOROLA、XYVOM、霍尼韦尔HONEYWELL 、力士乐REXROTH、KUKA、NI、DEIF、横河、伍德沃德WOODWARD、瑞恩、施耐德SCHNEIDER 、安川、 穆格MOOG、PROSOFT等品牌。

只卖库存产品;出完需订货!价格以客服说明为准!!订货货期以客服说明为准，有任何疑问请联繁客服! Limited stock, Contact US!

●使用前:

在操作和维护，安装设备之前，请阅读并严格遵守安全相关的信息。

Read and strictly follow safety-related information before operatingmaintainingand installing equipment.

●使用者要求:

必须从事安装，组装或维护设备等相关工控电气机械以及其他相关技术的人员。

Must be engaged in the installation,assembly or maintenance of equipment and other related industriacontroeectrica machinery and other related technica personne.应用范围:

应用于品牌本系列工业以及生产生活自动化设备产品。

Used in the brand of this series of industriaand production automation eauipment products

适用于场景:系统集成，非标定制，产线升级改造，原设备电气替换等等。

Suitable for scenarios:system integration,non-standard customizationproduction line upgrading and transformation,electrical replacement of original equipment,etc.

●操作人员:

应该由本品牌专业培训操作员来安装、操作和维修设备。专业人员具有技术能力强，熟悉安全信息和安全实施:

熟悉设备的安装加工、操作和维护:熟悉处理所有的潜在危险情况。

Equipment should be installed,operated and maintained by trained operators from the brand

●危险情况

警告

.请注意使用人员的人身安全。

●除了产品特性以及功能，还需了解产品的使用寿命环境。

●充分学习产品使用手册，否则非专业人员可能会造成人身危险。

Study the product instruction manual thoroughlyotherwise it may cause personal danger to non-professionals.

●服务行业

适用水泥，木业，石业，橡胶，石油，化工，发电，环保，水处理，制冷，交通，钢铁，食品，饮料，船舶，制冷等行业

Applicable to cementwood,stone,rubber,petroleumchemical, power generation