ENTERASYS A4H124-4FX网络交换机

产品详细资料
毫伏输入模块允许毫伏级信号，如桥接应变计（称重传感器）直接连接到PLC，而无需外部信号处理（传感器、变送器等）。信号的所有模拟和数字处理均在模块上执行。背板仅支持通用背板。使用PCI总线。无背板限制背板范围电压上占用的插槽模块数量1 1：+50mV、+150 mV、0–5 V、1–5 V，0–10 V、+10V±25 mV、±50 mV和±100 mV诊断开路、短路、正/负变化率N/A、高、高、低、低通道至通道隔离两组四个N/A通道数量8 4陷波滤波器是N/A分辨率11至16位，取决于配置范围和A/D滤波器频率，分别为3μV、6μV和9μV。25°C时的精度校准精度。优于量程的0.1%。±0.5%精度取决于A/D滤波器、数据格式、输入噪声和环境温度。输入阻抗>1M ohm>20 Mohms I/O所需N/A 4%AI A/D转换类型Sigma Delta积分A/D转换时间（假设2个ADC并行运行，无CJC或导线35通道/秒电阻）每个通道10ms*4通道=40ms（1KHz滤波器）每个通道127ms*4通道=508ms（8Hz滤波器）禁用的通道不扫描，缩短扫描时间。支持的应变计是桥接（称重传感器）大正常电压输入N/A 100 mV大电压输入±14.5 VDC连续±35 V连接器类型IC694TBBx32或IC694TBSx32。单独出售。接线板（20个螺钉），随模块一起提供。内部电源使用400 mA@5 V；350 mA@3.3 V 100 mA@5 VDC
The Millivolt Input Modules allow Millivolt level signals, such as bridged strain gages (load cells) to be directly connected to the PLC without external signal processing (transducers, transmitters, etc.) All analog and digital processing of the signal is performed on the module.Backplane Support Universal Backplane Only. Uses PCI Bus. No Backplane Restrictions Number of Slots Module Occupies 1 1 on Backplane Range Voltage: +50mV, +150 mV, 0–5 V, 1–5 V, 0–10 V, +10V ±25 mV, ±50 mV and ±100mV Diagnostics Open wire, Short Circuit, Positive/Negative Rate N/A of Change, High, High-High, Low, Low-Low Channel-to-Channel Isolation Two Groups of Four N/A Number of Channels 8 4 Notch Filter Yes N/A Resolution 11 to 16 bits, depending on configured range and A/D filter frequency 3 μV, 6μV, 9μV (respectively) Accuracy Calibrated Accuracy at 25°C. Better than 0.1% of range. ±0.5% Accuracy depends on A/D filter, data format, input noise, and ambient temperature. Input Impedance >1M ohm >20 Mohms I/O Required N/A 4% AI A/D Conversion Type Sigma Delta Integrating A/D Conversion Time (Assumes 2 ADC’s running in parallel, no CJC or lead 35 Channels/second resistance) 10ms per Channel* 4 Channels = 40ms (1KHz filter) 127ms per Channel* 4 Channels = 508ms (8Hz filter) Channels that are disabled are not scanned, shortening scan time. Strain Gages Supported Yes Bridged (load cells) Maximum Normal Voltage Input N/A 100 mV Maximum Voltage Input ±14.5 VDC continuous ±35 V Connector Type IC694TBBx32 or IC694TBSx32. Sold Separately. Terminal Block (20 screws), included with module. Internal Power Used 400 mA @ 5 V; 350 mA @ 3.3 V 100 mA @ 5 VDC
主营产品简介
专注于DCS、PLC、机器人控制系统、大型伺服四大系统领域。

主营产品各种模块/卡件，控制器，触摸屏，伺服驱动器。

优势：供应进口原装正品，专业停产配件，

发货快，货期精准，

主营品牌包括 ABB贝利、GE/FUANC、FOXBORO、英维思TRICONEX 、本特利BENTLY、A-B罗克韦尔、艾默生EMERSON 、OVATION、MOTOROLA、XYVOM、霍尼韦尔HONEYWELL 、力士乐REXROTH、KUKA、NI、DEIF、横河、伍德沃德WOODWARD、瑞恩、施耐德SCHNEIDER 、安川、 穆格MOOG、PROSOFT等品牌。

只卖库存产品;出完需订货!价格以客服说明为准!!订货货期以客服说明为准，有任何疑问请联繁客服! Limited stock, Contact US!

●使用前:

在操作和维护，安装设备之前，请阅读并严格遵守安全相关的信息。

Read and strictly follow safety-related information before operatingmaintainingand installing equipment.

●使用者要求:

必须从事安装，组装或维护设备等相关工控电气机械以及其他相关技术的人员。

Must be engaged in the installation,assembly or maintenance of equipment and other related industriacontroeectrica machinery and other related technica personne.应用范围:

应用于品牌本系列工业以及生产生活自动化设备产品。

Used in the brand of this series of industriaand production automation eauipment products

适用于场景:系统集成，非标定制，产线升级改造，原设备电气替换等等。

Suitable for scenarios:system integration,non-standard customizationproduction line upgrading and transformation,electrical replacement of original equipment,etc.

●操作人员:

应该由本品牌专业培训操作员来安装、操作和维修设备。专业人员具有技术能力强，熟悉安全信息和安全实施:

熟悉设备的安装加工、操作和维护:熟悉处理所有的潜在危险情况。

Equipment should be installed,operated and maintained by trained operators from the brand

●危险情况

警告

.请注意使用人员的人身安全。

●除了产品特性以及功能，还需了解产品的使用寿命环境。

●充分学习产品使用手册，否则非专业人员可能会造成人身危险。

Study the product instruction manual thoroughlyotherwise it may cause personal danger to non-professionals.

●服务行业

适用水泥，木业，石业，橡胶，石油，化工，发电，环保，水处理，制冷，交通，钢铁，食品，饮料，船舶，制冷等行业

Applicable to cementwood,stone,rubber,petroleumchemical, power generation